You push hard on the pedals and the chain suddenly slips, clunks or jumps to another gear. Skipping gears are frustrating and can be unsafe. The good news is that the cause is usually simple, and most of the time a proper tune-up sorts it out.
What "skipping" actually is
Your chain sits on a set of toothed rings: the cassette at the back wheel and the chainring at the pedals. The rear derailleur moves the chain across the cassette and holds it in line with the gear you've chosen. Skipping happens when the chain doesn't sit cleanly on the teeth. Under load, it rides up and over them, or drifts towards a neighbouring gear.
It tends to show up in a few ways:
- A sudden slip or jolt when you pedal hard, often when climbing or setting off.
- Constant clicking or chattering in one or two gears.
- The bike changing gear by itself without you touching the shifter.
- Shifts that are slow, hesitant or need an extra click to happen.
When the chain slips under load, your foot can drop suddenly. That's the safety issue, especially in traffic or when standing up on the pedals.
The most common causes
1. Cable tension has changed
This is the number one cause on bikes with cable-operated gears. Gear cables bed in and stretch slightly with use, especially on newer bikes. As the tension drops, the derailleur no longer lines up exactly with each gear. The chain sits halfway between two cogs and jumps about.
2. A bent derailleur hanger
The hanger is a small metal piece that connects the rear derailleur to the frame. It's designed to bend in a knock to protect the frame, and it bends easily. Laying the bike down on its drive side, a fall, or bikes crammed together in a car park or building storage room can all do it. Once it's bent, the gears will never shift perfectly, no matter how you adjust the cable.
3. A worn chain, cassette or chainring
Chains wear and lengthen slightly as you ride, which people often call "chain stretch". A worn chain no longer fits the teeth properly, and it also wears the cassette and chainring faster. Eventually, the teeth become hooked or shark-fin shaped. If you fit a new chain onto a badly worn cassette, it can skip even more until the cassette is replaced too.
4. Dirt, sand and dried-out lube
In Dubai, this one deserves its own heading. Fine sand and dust stick to oily chains and build up into a gritty paste. That paste stiffens the chain links, clogs the jockey wheels on the derailleur and speeds up wear. Heat can also dry lubricant out quickly, leaving links stiff. A stiff link is one of the classic causes of a chain that "jumps" once every pedal revolution. Our guide to keeping grit out of your drivetrain explains how to stay on top of this.
5. Damaged or dirty cables and housing
Even with the right tension, a cable that is rusty, frayed or packed with grit inside its outer housing won't move smoothly. Shifts lag, and the derailleur doesn't return cleanly to position. Bikes stored on balconies or near the coast are more prone to this because of the sun and humidity.
6. Loose parts
A loose rear wheel, a loose cassette lockring or a loose derailleur mounting bolt can all cause skipping or clunking. These are less common, but they're worth ruling out.
Checks you can do at home
- Clean and lube the chain. Wipe it with a rag, clean off the grit, then apply a lube suited to dry, dusty conditions and wipe off the excess. See choosing the right chain lube for desert conditions.
- Look for stiff links. Turn the pedals backwards slowly and watch the chain pass through the rear derailleur. A stiff link will kink or jump as it goes through.
- Check the wheel. Make sure the rear wheel is fully seated in the frame and the quick-release or thru-axle is tight.
- Look at the hanger from behind. Stand behind the bike and look at the rear derailleur. It should hang straight down, parallel to the cassette. If it's tilted inwards, the hanger is likely bent.
- Try a small barrel adjuster tweak. Many bikes have a barrel adjuster where the cable enters the derailleur or shifter. If the chain is slow to move to bigger cogs, a quarter turn anticlockwise often helps. Go slowly, a quarter turn at a time, and test after each one.
Tip: if you've adjusted the barrel more than a full turn and things are getting worse, stop. The problem is probably the hanger, the cable or worn parts, and more adjustment won't fix it.
What a tune-up involves
A proper gear tune-up looks at the whole system, not just one screw. Our mechanics clean the drivetrain, check chain wear, inspect the cables and housing, check the hanger alignment, set the limit screws so the chain can't fall off either end of the cassette, and then set the cable tension so every gear shifts cleanly. Finally, everything is tested under load, not just with the bike standing still.
If the chain, cassette or another part is worn beyond adjustment, we'll explain what we've found and tell you the cost before fitting anything.
Which service to book
Gear servicing is included in our Basic package at 150 AED. If your gears are skipping, our Standard package at 200 AED adds full gear tuning, alignment and adjustment, plus a torque check on the crank arms and chainring. For a bike that's covered in grime, the Premium package at 250 AED adds a full drivetrain deep clean and lubrication. Not sure which fits? Read Basic, Standard or Premium: which bike service do you need?, or simply book a visit and tell us what's happening.
Let us handle it
Our mechanics come to your home anywhere in Dubai. Bike packages from 150 AED. Book in 60 seconds on WhatsApp.